3G Shield

Started by RiffRaff, September 19, 2013, 07:59:06 AM

Previous topic - Next topic

RiffRaff

*
Newbie
Posts: 2
Logged
Hi Guys

thinking a shield that has 3G/4G micro sim card, combined with GPS would be very handy for tracking

cheers Riff

tomcUT

***
Full Member
Posts: 21
Logged

raminf

*
Newbie
Posts: 1
Logged
Yes!

I'm backing this one http://www.kickstarter.com/projects/sparqee/sparqee-cellv10-cellular-made-easy-arduino-pi
but it would be great if it could be made to work in a Tiny form factor.

chall2009

*
Newbie
Posts: 1
Logged
I'm going to through in my support for this one as well!

wafel

***
Full Member
Posts: 12
Logged
Vote+!

That would be just awesome!

tomcUT

***
Full Member
Posts: 21
Logged

hwt

*
Newbie
Posts: 1
Logged
Hello all,

I urgently need such a Shield for a tracking project. Very good idea!

raulp

*
Newbie
Posts: 1
Logged
#7
Vote++;
A micro antena?

hackman

**
Jr. Member
Posts: 5
Logged
I will also want 3G/4G shield, but there should be two options for the antenna, built-in and external. It is pretty hard to solder smt connector on these thin PCBs :)

tinybuilder

***
Full Member
Posts: 27
Logged
#9
That would be a nice addition. Even a cellular modem without voice capability would be quite useful.

I know of 3 GSM modules that may be small enough to work with on a shield the size of the "TinyShield Proto Terminal Blocks" (I don't know the exact size of that board but it looks about 26x30 mm) - the uBlox SARA-U2 series (16x26x3 mm), the Telit UL865 (24.4x24.4x2.6 mm), and the SIMcom sim900 (24x24x3 mm)

Using the "TinyShield Proto Terminal Blocks" as a starting point, the connector and mounting holes for the shield would have to be shifted back towards the connector edge so the GSM module could be squeezed onto the board. A SIM card holder would need to be mounted under the board. A U.FL connector for the antenna, a TRRS 2.5 mm jack for ear/voice, and all other support circuitry should probably be put onto the bottom side of the shield. Many of these GSM module's features require lots of pins... this would impact what other shields could be used in the stack. These pins would have to be sussed out to see which ones could be ignored.

A good start on a wiring diagram and components for a Telit UL865 can be found at http://www.mikroe.com/downloads/get/1921/gsm_click_manual_v101b.pdf for the MikroElektronika GSM click. I could only find code for a project using the Telit gm862 http://tinkerlog.com/2009/05/15/interfacing-arduino-with-a-telit-gm862/ which could be somewhat helpful.

A great project using the SIM900 is the Arduino Phone found on Instructables
Instructions: http://www.instructables.com/id/ArduinoPhone/?ALLSTEPS
Code on GitHub: http://yexiaobo-seeedstudio.github.io/ArduinoPhone/

wfalkwallace

Guest
Logged

alexcc

*
Newbie
Posts: 1
Logged
vote++

I have been searching in the market but all available units seem to be far too big

katysei

***
Full Member
Posts: 11
Logged
great idea.
its almosta must this days.

katysei

***
Full Member
Posts: 11
Logged

mroz

*
Newbie
Posts: 1
Logged
I'd be all over a TinyGSM module like a cheap suit....


SMF spam blocked by CleanTalk