TinyCircuits Forum
General Category => General Discussion => Topic started by: darksheep on July 01, 2013, 06:50:54 AM
-
Any one know if there is a screen out there that is the same size as the tiny shields that I could use with my project.
So 20mm by 20mm or jsut a bit bigger is fine as well.I it operated at 3v3 volts that would be amazing as well.
-
This one is 3.3v / 20mA. It is 28mm x 28mm, so slightly larger than what you want: http://www.digikey.com/product-detail/en/COG-C144MVGI-08/153-1146-ND/2523706
This one is slightly smaller, but might need a little more effort on the programming side (also wants 3.5v for the backlight instead of just 3.3v like on the logic pins): http://www.digikey.com/product-detail/en/NHD-12864WX-T1TFH%23/NHD-12864WX-T1TFH%23-ND/2165862
If your pockets are deep, then there are also these which all seem to be in the size range you are looking for (although not very thin): http://www.digikey.com/product-search/en?FV=fff40008,fff80276,ffec322b&stock=1
Lastly, there are a couple of displays from Adafruit which might be suitable. They tend to be slightly larger than 20x20, but maybe that is OK for your needs:
http://www.adafruit.com/products/1393#Description
http://www.adafruit.com/products/326#Description
None of those screens will have the Tinyduino connector - you would probably need to make a small board for any of them, or possibly wire it up to a Tinyduino Protoboard.
-
If your pockets are deep, then there are also these which all seem to be in the size range you are looking for (although not very thin): http://www.digikey.com/product-search/en?FV=fff40008,fff80276,ffec322b&stock=1
This one loooks amazing have you seen any one use it with an arduino ?
-
No, I have not. I would caution you though about relying too much on the images shown in those listings. The one with the fish photograph looks very suspicious to me. I think it was photoshopped. The others might be more reasonable, but still... I just wouldn't trust the product pictures.
-
Actually we did use one of those NKK OLEDs for an initial proof of concept and it's shown in the Kickstarter video. Attached is a pict of this, it worked fairly well and is easy to program and the pictures are good, but it is very pricey.
Thanks,
Ken
(http://www.wired.com/design/wp-content/uploads/2012/09/Tiny_with_LCD-660x605.jpg)
-
I'm impressed. The image quality is a lot better than I presumed it would be. Almost looks like it was made to fit the TinyDuino boards.
-
It's actually quite tall though, which is a bit of a pain. It also requires a high voltage for the LCD drive (think around 11 or 12V) - the orange wire on the side is running off to a bench supply, so it's not easy to interface too.
Ken
-
MMM looks cool may be you guys could make a shield for it ;)
I think I might end up going with this http://www.adafruit.com/products/1393.
Its small and lowish power so might work well.
-
Actually we did use one of those NKK OLEDs for an initial proof of concept and it's shown in the Kickstarter video. Attached is a pict of this, it worked fairly well and is easy to program and the pictures are good, but it is very pricey.
Thanks,
Ken
(http://www.wired.com/design/wp-content/uploads/2012/09/Tiny_with_LCD-660x605.jpg)
Those screens remind me of this keyboard: the lcd keyboard:
http://www.it2info.com/article3853.html (http://www.it2info.com/article3853.html)
-
Some sources
.66 inch (16.764 mm)
http://www.buydisplay.com/default/oled-display/64x48-dot-matrix-0-66-oled-display-module-with-datasheet-price-pinout-arduino-serial-spi-interface-from-china-manufacturer-supplier
0.83 inch (21.082 mm)
http://www.buydisplay.com/default/96x39-pixel-0-83-inch-small-oled-display-manufacturers-i2c-serial-spi
0.96 inch (24.384 mm)
http://www.buydisplay.com/default/monochrome-0-96-inch-128x64-oled-display-module-ssd1306-blue-and-yellow
http://www.gabotronics.com/electronic-kits-modules/graphic-0.96-oled-display.htm
-
can i use this screen or is there another one ?
https://learn.adafruit.com/096-mini-color-oled/wiring
-
will the tiny screen be usable with arduino ?
https://www.kickstarter.com/projects/kenburns/tinyscreen-a-color-display-the-size-of-your-thumb (https://www.kickstarter.com/projects/kenburns/tinyscreen-a-color-display-the-size-of-your-thumb)
This is a major question to me thanks for replying ..
I was un able to find the answer anywere
It scares me if i by one and there will be not cheap way to adapt it it zill be a mess !
Thanks Leo .
-
will the tiny screen be usable with arduino ?
https://www.kickstarter.com/projects/kenburns/tinyscreen-a-color-display-the-size-of-your-thumb (https://www.kickstarter.com/projects/kenburns/tinyscreen-a-color-display-the-size-of-your-thumb)
This is a major question to me thanks for replying ..
I was un able to find the answer anywere
It scares me if i by one and there will be not cheap way to adapt it it zill be a mess !
Thanks Leo .
You mean like a standard BIG Arduino? I would say no. Well you can connect the TinyScreen to the Tinyshield proto blocks:
https://tiny-circuits.com/tiny-shield-proto-terminal-blocks.html
Just buy it without the green blocks. then you can solder it to any type of arduino you want.