76
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
77
New Product Ideas / Re: breadboarding cable
« on: October 05, 2013, 07:27:39 AM »Tiny ribbon connector on one end and male jumper wires on the other end.
Can be used for testing circuits quickly on a solderless breadboard.
Jumper wire ends are labeled somehow.
We kind of already have a board like this, we use it for testing. I'll ask Ken if he can put some up for sale.
78
TinyLily / Re: Pinout documentation
« on: October 05, 2013, 07:24:28 AM »
You can hook up more lights by using "Charley plexing" You can use this schematic:
http://tiny-circuits.com/wp-content/uploads/2012/09/ASD2411_Rev3.pdf
http://tiny-circuits.com/wp-content/uploads/2012/09/ASD2411_Rev3.pdf
79
TinyLily / Re: Broken TinyLily USB Shield?
« on: October 05, 2013, 06:52:18 AM »
Yeah those don't have a key to help with alignment.
80
New Product Ideas / Re: 9 DoF sensor fusion shield
« on: October 05, 2013, 06:50:22 AM »
We have a 9axis board in development
81
New Product Ideas / Re: zigbee or z-wave ?
« on: October 05, 2013, 06:46:17 AM »
You could just use I2C to communicate to a zigbee
82
TinyLily / Re: tinylily motor driver
« on: September 25, 2013, 06:09:40 AM »
You can connect the tinylily motor controller to the TinyDuino's proto board. If all that your driving is 1 motor it should be fine running off the one coin cell. If you need more power then you can connect an external power supply to the TinyDuino and just leave the coin cell out.
83
TinyDuino Processors & TinyShields / Re: Servos question.
« on: September 25, 2013, 06:04:42 AM »
It won't hurt the circuit if the servos need more power.
If the servos run out of power your project just won't work, it will act like an RC Car when the batteries go dead. If you see this happen then I would should jest using a wall wart (power supply) to run your project.
If the servos run out of power your project just won't work, it will act like an RC Car when the batteries go dead. If you see this happen then I would should jest using a wall wart (power supply) to run your project.
84
New Product Ideas / Re: Tiny ribbon connectors to allow different layouts
« on: September 25, 2013, 05:58:47 AM »
I think I have the general idea of what you want, can you draw up a sketch of how you want the ribbon and boards laided out?
Would be nice to come up with a common Flexible Printed Circuit Board (ribbon cable) that would work for multiple layouts.
Would be nice to come up with a common Flexible Printed Circuit Board (ribbon cable) that would work for multiple layouts.
85
User Projects / Code Examples / Re: accelerometer LED G-force display
« on: September 06, 2013, 05:55:09 AM »
In your loop, you will want to:
1> read what the AccelX is
2> use a select case statement to decide how many LEDs to light up
3> turn on those LEDs
Hope that helps
1> read what the AccelX is
2> use a select case statement to decide how many LEDs to light up
3> turn on those LEDs
Hope that helps
86
New Product Ideas / Re: Adding I/O and Higher current to Tiny's. AND blank pre drilled boards!
« on: September 06, 2013, 04:59:20 AM »
We have a die that trims the round lilys so we Might be able to cut out blank round boards. Drilling all those holes would take some time though.
87
User Projects / Code Examples / Re: accelerometer LED G-force display
« on: August 29, 2013, 04:22:39 AM »
Can you post the code that you have so far?
I might be able to help you modify it.
I might be able to help you modify it.
88
TinyLily / Re: Any reviews of TinyLily?
« on: August 26, 2013, 07:00:32 AM »
How close are you to Akron? You'r welcome to stop by and check them out for yourself.
89
New Product Ideas / Re: 10 segment LED bar graph Multi colored leds
« on: August 23, 2013, 04:40:10 AM »
Can you draw a sketch of how you would want the LEDs laid out?
You could take a standard LED shield and replace the LEDs with the green yellow and red LEDs.
You could take a standard LED shield and replace the LEDs with the green yellow and red LEDs.
90
New Product Ideas / Re: Inductive wireless charging
« on: August 21, 2013, 06:13:54 AM »
Yeah just like Pit Road on F-Zero!
SMF spam blocked by CleanTalk