Messages

1

General Discussion / Re: TSV Video conversion issues

« on: February 22, 2021, 04:40:35 PM »

Doppelganger,

I'm also looking forward to your experiences with this device, as some non-technical types have asked me how to upload videos to this unit.

-john

2

General Discussion / ZOE GPS TinyShield Update??

« on: February 18, 2021, 05:02:44 PM »

Any news as to when the ZOE GPS TinyShield will become available?

Any details on same would be appreciated so we can plan on implementations.

Thanks...john

3

General Discussion / Re: ZOE GPS proto board / ZOE setup with examples

« on: December 21, 2020, 05:18:24 PM »

Ben,

How can one charge the battery if the UART (USB port, I assume) is being used for this board? Let me know if I'm off base on this.

BTW, a 20mm x 20mm board would be fantastic!

Thanks,
John

4

General Discussion / Re: ZOE GPS proto board / ZOE setup with examples

« on: December 17, 2020, 11:53:14 AM »

WillemH said...

"With my model rocket application with UART only I have shown that it is not strictly necessary to have access to the I2C, ]but access to both UART and I2C will certainly increase the attractiveness of the new board"

I concur...john

5

General Discussion / Re: Plant Monitor Kit Tutorial Photo

« on: November 21, 2020, 05:22:07 PM »

Thanks for getting the photo up here ...https://learn.tinycircuits.com/Wireling-Projects/Plant-Monitor_Tutorial/

-john

6

General Discussion / Re: ZOE GPS proto board in 35 mm model rocket application / Introduction

« on: November 21, 2020, 12:58:55 PM »

WillemH,

Would it be possible to acquire your BMA250 accelerometer csv files from your test flights?

- acceleration (3 axes simultaneously) and temperature of BMA250 on TinyZero,

Also, what were your bandwidth and acceleration range settings at the time.

Thanks,

John

7

General Discussion / Plant Monitor Kit Tutorial Photo

« on: November 19, 2020, 08:15:45 PM »

Looks like the Plant Monitor Kit Tutorial page may need a photo at the top.
https://learn.tinycircuits.com/Wireling-Projects/Plant-Monitor_Tutorial/

-john

8

General Discussion / Re: How To Access Wireling A0 - A3 Ports

« on: October 28, 2020, 09:38:16 PM »

Please ignore the preceding question about the Wireling ....I found the answer to my coding questions in the Large Button section https://tinycircuits.com/collections/wireling-input-output/products/large-button-wireling  under Software.

It works!

Sorry for the intrusion,

John

9

General Discussion / How To Access Wireling A0 - A3 Ports

« on: October 28, 2020, 02:57:40 PM »

I have a Wireling Adapter TinyShield   ASD2022 (only one) connected to a TinyZero Processor Board      ASM2021-R-A

I am trying to access either A1, A2 or A3....A0 is used for the 0.42 OLED that seems to work fine. 

Here's part of my code....

Defining the pin
const int       apb   = A1;                   //use A1 as the altitude push button (apb)on the Wireling

Trying to access the analog value
  Wireling.selectPort(apb);                //Select Wireling port
  apb_value = analogRead(apb);             //get the value of the analog port

When opening or closing a push button on this port, I get the same analog value (15 out of 1023)

What do I need to do differently?

Thanks,
John

10

General Discussion / Re: More Dual Motor Board Software Questions

« on: October 21, 2020, 01:01:28 PM »

Réna....thanks...john

11

General Discussion / More Dual Motor Board Software Questions

« on: October 20, 2020, 06:35:41 PM »

Are there a (complete) set of motor commands as hinted in the "TinyCircuits Dual Motor Driver Basic Example"

for example...
  motor.setFailsafe(1000);
    motor.setMotor(1,i);
    motor.setMotor(2,i);

Are there any more like this??

Thanks,
John

12

General Discussion / Re: Motor Driver Issue

« on: October 20, 2020, 03:33:41 PM »

Réna,

Thanks for the info...that seemed to do it, for now.

Regards....john

13

General Discussion / Motor Driver Issue

« on: October 20, 2020, 01:20:33 PM »

In attempting to compile the //  TinyCircuits Dual Motor Driver Basic Example - and after installing the <MotorDriver.h>, I get the following error message....'NO_R_REMOVED' was not declared in this scope...

Any ideas as to what I'm doing incorrectly - like die I install the "right" lib?

Thanks,
John

14

General Discussion / Re: Duel Motor TinyShield Schematic Issue

« on: October 06, 2020, 01:04:59 PM »

Rena,

This is what I was looking for...thanks....john

15

General Discussion / Re: Duel Motor TinyShield Schematic Issue

« on: October 05, 2020, 02:21:27 PM »

Rena,

Thanks for the fix!

Question....do mating connectors with wires exist so that one can connect (plug in) a DC motor to the board (and solder the wire ends to the motor_?

John